Concrete Blocks and Cement Bricks: Sizes, Uses and Counts
"Cement bricks" usually means bricks or blocks made from concrete: Portland cement, sand, fine aggregate and water, pressed or vibrated into molds and cured, rather than clay fired in a kiln. The large hollow ones are concrete masonry units (CMU, often called cinder blocks), and the small solid ones are concrete bricks. This page covers the common sizes, how to tell nominal from actual dimensions, what they are used for, and how to count them for a wall.
Blocks, bricks and the standards behind them
| Unit | US standard | What it is |
|---|---|---|
| Load-bearing concrete block | ASTM C90 | Hollow or solid CMU for walls that carry loads |
| Non-load-bearing concrete block | ASTM C129 | Partitions, screens and walls that carry no structural load |
| Concrete building brick | ASTM C55 | Solid, brick-sized concrete units, often for veneer, garden walls and paving-type uses |
Outside the US, solid and hollow concrete blocks are made to national standards in a range of metric sizes, for example 400 x 200 x 200 mm units. Check what your local supplier stocks before planning dimensions.
Nominal and actual sizes
Masonry units are named by their nominal size, which includes a standard 3/8 in (10 mm) mortar joint. The unit itself is 3/8 in smaller in each direction, so that one unit plus one joint equals the nominal dimension.
| Unit | Nominal (W x H x L) | Actual |
|---|---|---|
| Standard 8 in block | 8 x 8 x 16 in | 7 5/8 x 7 5/8 x 15 5/8 in (194 x 194 x 397 mm) |
| 6 in block | 6 x 8 x 16 in | 5 5/8 x 7 5/8 x 15 5/8 in |
| 4 in block | 4 x 8 x 16 in | 3 5/8 x 7 5/8 x 15 5/8 in |
| Modular concrete brick | 4 x 2 2/3 x 8 in | 3 5/8 x 2 1/4 x 7 5/8 in |
So an 8 in block wall rises 8 in per course and a 16 in block covers 16 in of length per unit, joint included. That makes it easy to plan wall lengths and heights in multiples of 8 in so you cut fewer blocks.
Shapes you will see
- Stretcher: the standard block, with flanged or plain ends.
- Corner: one flat, finished end for wall ends and corners.
- Half block: 8 in long, to finish courses without cutting.
- Bond beam and lintel blocks: U-shaped or with knock-out webs, to hold horizontal rebar and grout, and to span openings.
- Solid and cap blocks: for tops of walls and where a solid bearing surface is needed.
Weight
A normal-weight hollow 8 x 8 x 16 in block typically weighs roughly 35 to 40 lb (16 to 18 kg); lightweight-aggregate blocks are lighter, around 25 to 30 lb; solid units are much heavier. A pallet can weigh well over a ton, which matters for trailers, floors and where the delivery truck sets it down. Check the supplier's figure for the exact product.
What they are used for
- Foundation and basement walls, load-bearing walls and retaining walls. These are structural. Wall thickness, reinforcement, grout, footing size and drainage come from the plans, a structural engineer and the local building code, and many need a permit. Retaining walls in particular can fail suddenly when soil pressure builds behind them.
- Garden walls, planters, outdoor kitchens, barbecue surrounds, shed and garage walls. Still need a proper footing below frost depth where frost is a concern, and good drainage.
- Concrete brick for veneer, garden walls, edging and paths where a brick look is wanted with concrete's consistent size.
In reinforced block walls, vertical rebar runs through some of the hollow cores, which are then filled solid with grout (a fluid concrete-like mix), and bond beams carry horizontal bars. Where cores are grouted and how often is part of the design.
How to count blocks and bricks for a wall
Blocks
The face of an 8 x 16 in block with its mortar joint is 8 x 16 = 128 sq in, about 0.89 sq ft, so you need 1.125 blocks per square foot of wall face.
- Wall area = length x height. Example: 20 ft long, 6 ft high = 120 sq ft.
- Subtract door and window openings.
- Blocks = area x 1.125. 120 x 1.125 = 135 blocks (check: 15 blocks per 20 ft course x 9 courses in 6 ft = 135).
- Add wastage for breakage and cuts: 10% is a common default. 135 + 10% = 149 blocks.
Order corner and half blocks for each wall end and course as needed; they replace stretchers rather than adding to the count.
Bricks
Modular brick laid with 3/8 in joints, three courses to every 8 in of height, works out to about 6.75 bricks per square foot of single-wythe (one brick thick) wall. For the same 120 sq ft wall, that is 810 bricks, or about 891 with 10% added. A double-wythe wall needs twice as many.
Our block and brick calculator uses 0.89 sq ft per block and a 10% default wastage, which gives the 149 blocks above, and the modular brick face with its joint (8 x 2 2/3 in nominal), so its brick count matches the 6.75 figure. If your brick is a different size, divide 144 by the nominal face area in square inches to get bricks per square foot.
For the mortar to lay them, see how much mortar you need for a block or brick wall.
Cutting block and brick
Blocks can be split with a brick set (a wide chisel) and hammer along a scored line, or cut with a masonry saw. Cutting, grinding or chiseling concrete block or brick releases respirable crystalline silica, which causes lung disease. Use a wet saw or a saw with on-tool dust extraction, wear a properly fitted respirator and eye protection, keep others away, and clean up with a HEPA vacuum or wet methods, never by dry sweeping. Where you can, plan the wall around half blocks to cut less.
Safety when laying
- Lifting. Laying a wall means lifting a 35 to 40 lb block hundreds of times. Keep blocks stacked at waist height near the work, lift with your legs, avoid twisting, and share the load.
- Gloves. Wear alkali-resistant gloves: blocks are abrasive, and wet mortar is strongly alkaline and can cause chemical burns and allergic skin reactions. Wash mortar off skin promptly with clean water; rinse eyes for at least 15 minutes and get medical help if any gets in.
- Fresh walls. A newly laid wall has little strength until the mortar cures. Brace tall walls against wind and do not backfill against a block wall until the engineer or plans say it is ready.