CONSTRUCTION
- if you’re going to be installing concrete patio slabs, try to think about how much concrete is needed for your space. This can be done by measuring the length and width of your space.
- A great way to mix up the concrete is to use a rototiller which can mix up large amounts in just a couple of minutes. If you don’t have one on hand, then you should consider renting one from a local equipment rental store or even Home Depot or Lowe’s.
- concrete needs to be kept wet while it is being used, so if there is any type of moisture in the air, then make sure that you are using enough water when mixing it.
- Other than that, it’s pretty easy once you get started and figure out what works best for your project.
1. Check the potential location of your patio. 2. Dig a 1-foot deep by 12-inch wide trench around your patio, running parallel to the existing ground. 3. Take a spade and sculpt the existing soil into a flat or gently sloping surface that will become your patio base, or create a formal patio bowl shape. 4. Compact the area where you are going to cast your concrete or stone patio slab. 5. Lay out your area with a string line and pegs and drive stakes into each corner of the perimeter of your patio and attach string lines to those stakes to create an accurate guide for the location of your edging, if you are using it. 6. Install plastic barriers, such as Visqueen, over your excavated areas and situate them between your edging materials, if you want to prevent water from seeping through the concrete onto adjacent soil and plants or from under and around the edges of your concrete slab, which could freeze in colder climates and cause cracking
- Check the potential location of your patio.
- Dig a 1-foot deep by 12-inch wide trench around your patio, running parallel to the existing ground.
- Take a spade and sculpt the existing soil into a flat or gently sloping surface that will become your patio base, or create a formal patio bowl shape.
- Compact the area where you are going to cast your concrete or stone patio slab.
- Lay out your area with a string line and pegs and drive stakes into each corner of the perimeter of your patio and attach string lines to those stakes to create an accurate guide for the location of your edging, if you are using it.
- Install plastic barriers, such as Visqueen, over your excavated areas and situate them between your edging materials, if you want to prevent water from seeping through the concrete onto adjacent soil and plants or from under and around the edges of your concrete slab, which could freeze in colder climates and cause cracking
CONSTRUCTION
if you’re going to be installing concrete patio slabs, try to think about how much concrete is needed for your space. This can be done by measuring the length and width of your space.
A great way to mix up the concrete is to use a rototiller which can mix up large amounts in just a couple of minutes. If you don’t have one on hand, then you should consider renting one from a local equipment rental store or even Home Depot or Lowe’s.
concrete needs to be kept wet while it is being used, so if there is any type of moisture in the air, then make sure that you are using enough water when mixing it.
Other than that, it’s pretty easy once you get started and figure out what works best for your project.
1. Check the potential location of your patio. 2. Dig a 1-foot deep by 12-inch wide trench around your patio, running parallel to the existing ground. 3. Take a spade and sculpt the existing soil into a flat or gently sloping surface that will become your patio base, or create a formal patio bowl shape. 4. Compact the area where you are going to cast your concrete or stone patio slab. 5. Lay out your area with a string line and pegs and drive stakes into each corner of the perimeter of your patio and attach string lines to those stakes to create an accurate guide for the location of your edging, if you are using it. 6. Install plastic barriers, such as Visqueen, over your excavated areas and situate them between your edging materials, if you want to prevent water from seeping through the concrete onto adjacent soil and plants or from under and around the edges of your concrete slab, which could freeze in colder climates and cause cracking
Check the potential location of your patio.
Dig a 1-foot deep by 12-inch wide trench around your patio, running parallel to the existing ground.
Take a spade and sculpt the existing soil into a flat or gently sloping surface that will become your patio base, or create a formal patio bowl shape.
Compact the area where you are going to cast your concrete or stone patio slab.
Lay out your area with a string line and pegs and drive stakes into each corner of the perimeter of your patio and attach string lines to those stakes to create an accurate guide for the location of your edging, if you are using it.
Install plastic barriers, such as Visqueen, over your excavated areas and situate them between your edging materials, if you want to prevent water from seeping through the concrete onto adjacent soil and plants or from under and around the edges of your concrete slab, which could freeze in colder climates and cause cracking
Anns is a contributor at PanyamCements. We are committed to providing well-researched, accurate, and valuable content to our readers.
