When you are a busy worker, you don’t always have time to change shoes before you leave work. If you work with cement, it could stain your shoes and make them look dirty. Most people assume that once cement dries on a shoe, it is there forever. This is not true. You can remove cement from your shoes with a few simple steps. With some elbow grease, a little time and the right ingredients, you can remove cement stains from your shoes and have them looking like new again.

Step 1: Scrape

Remove as much of the dry cement from the shoe as possible by scraping it off with a knife or a spoon. Do not use sharp objects like a razor blade or box cutter because they could damage the shoe permanently. If there are any pieces that are still stuck to the shoe, use the edge of a credit card to scrape them off gently.

Step 2: Soak

Fill a bucket with warm water and add two drops of dish detergent to the water to create suds. Place your shoes in the bucket, making sure they are entirely submerged under water so that they soak up enough water to soften up any remaining cement on them. Let them soak for at least an hour or until you notice that all of the cement is

We’ve all been there before. You’re standing in a field of freshly poured concrete, when your boss asks to see you about a new project. You walk across the wet cement and back again, with fresh cement stains on your shoes.

Don’t worry! We have 3 simple steps you can take to remove cement stains from your shoes.

1) Remove the excess concrete with a shoe brush or other hard surface like a brick.

2) Go to the store and buy some acetone nail polish remover. Apply it to the cement stain with a soft cloth and rub until it comes out.

3) Repeat step 2 until satisfied.

Before beginning, it is important to note that this is not a one-step process. In order to completely eliminate the stain, you will have to repeat the steps below several times until your shoes are clean.

Step 1: Soak your shoe in hot water for at least 5 minutes. The hotter the water, the better.

Step 2: Create a paste out of baking soda and water, then gently apply it with a cloth or scrubber and rub the stain for about 5 minutes.

Step 3: Repeat Step 1.

If you follow these steps, there is no reason why you should not be able to remove cement from your shoes in no time!

If you’ve ever left a cement project, only to find that you’ve got cement stains on your shoes, then you’re in luck. Cement stains are actually pretty easy to remove.

Here are 3 easy steps to get rid of those unsightly cement stains.

Step 1:

Gently scrub the shoes with a soft brush or toothbrush to remove as much of the stain as possible. Don’t rub too hard, it’s important to avoid spreading the stain and damaging the shoe.

Step 2:

Mix baking soda and water into a thick paste and apply it to the cement stains. Allow this paste to sit for about 30 minutes. Then wipe off with a damp cloth. Repeat if necessary.

Step 3:

If there are still stains remaining, mix some vinegar and water at a 1-to-1 ratio. Dip a sponge into the solution and gently wipe away any remaining cement stains from your shoes. Wash with soap and cold water afterwards to remove any trace of the vinegar smell, then allow shoes to dry completely before wearing them again.

Removing cement stains from shoes is not as difficult as you might think. If you have done some concrete work, or construction then at some point you are going to need to know how to remove cement stains from your shoes. This is a very simple process that will only take about 30 minutes for most jobs.

The problem with removing cement stains from shoes is that the dirt has worked its way into the fabric of the shoe and it can’t be easily brushed off. Even if you do manage to brush off some of the dirt it still leaves a white streak where the dirt was removed. This is why I recommend using a strong cleaning solution with an abrasive element such as a scrub brush or toothbrush. A toothbrush should be used on the inside of the shoe, while a scrub brush should be used on the outside of the shoe.

The reason why you want to use an abrasive element is because it will help loosen up any dirt that is stuck in between the fibers of your shoes. You can also use a scrub brush on the outside of your shoes to remove any excess dirt that may have made its way into your shoe’s crevices. Once this step has been completed, all you will need to do is rinse off your shoes with water and then let

Step 1: Wet the stain slightly by sprinkling water on it.

Step 2: Mix a solution of 4 parts warm water, 1 part detergent and 1 part ammonia. Place the solution in a spray bottle and spray the cement stained area.

Step 3: Let it sit for about 10 minutes and then rinse with warm water.

Good luck getting that stubborn stain out!